MicroLight
Flight
Simulator
The Hardware is used to operate 'real' instruments using:
Fs2004 or FSX
A registered or unregistered version of Peter Dowsons excellent FSUIPC
Our FSUIPC2RS232 software interface.
Input/Outputs
Info
Suggested Use
Analog 1
0-12v 8bit
EGT
Analog 2
0-12v 8bit
CHT
Stepper Expansion/ 3 Servo drive
Software programmable as
DIR (Direction)
EN (Enable)
CLK (clock)
or 3 Standard servo Outputs
ALT
8 GPIO
Individually Programmable as:
GPIO
Pulse
Servo
Servo Expansion
Stepper Expansion
Servo
ASI
Servo
VSI
Pulse
RPM
Servo
WATER Temperature
Servo
Oil Pressure
Servo
Oil Temperature
GPIO
Green Battery
GPIO
Red Battery
Expansion Output
This Output allows for a
RELAY expansion board consisting of:
6 SPDT Relays
2 Solid State Relays
The 8 open collector drivers for the above
and
Solid State Relay expansion board consisting of:
1 DPDT Relays
7 Solid State Relays
The 8 open collector drivers for the above
or
A Stepper expansion board
or
A Standard Servo expansion board
1 SPDT Relay
In flight
RS232 1
Allocated to PC communication
RS232 2
Reserved
RS485
Allocated to Flydat Echo
Power IN
5v DC Regulated and 12v DC Regulated
Hardware Interface to Flight Instruments MLFS 2
MicroLight
Flight
Simulator
The Hardware is used to operate 'real' instruments using:
Fs2004 or FSX
A registered or unregistered version of Peter Dowsons excellent FSUIPC
Our FSUIPC2RS232 software interface.
Input/Outputs
Info
Suggested Use
Analog 1
0-12v 8bit
EGT
Analog 2
0-12v 8bit
CHT
Stepper drive
Unipolar
ALT
4 GPIO
Individually Programmable as GPIO, Pulse or Servo
Can also be programmed for Servo Expansion (9 off) or Stepper Expansion
Servo
ASI
Servo
VSI
Pulse
RPM
Servo
WATER Temperature
4 Relays
1 DPDT 3 SPDT
1 DPDT
Inflight
3 DPDT
Spare
4 Open Collectors
Green Battery
Red Battery
2 Spare
8 GPIO
Individually Programmable as:
GPIO
Pulse
Servo
Servo Expansion
Stepper Expansion
Servo
Oil Pressure
Servo
Oil Temperature
6 Spare
RS232
Allocated to PC communication
Power IN
5v DC Regulated and 12v DC Regulated
Stepper Expander for MLFS 1 or 2
The Stepper Expander allows the Simmer to attach
Stepper Driven Instruments to either MLFS 1 or 2
The Stepper motor can be unipolar or bipolar
Relay Expander for MLFS 1
The RELAY expansion board allows:
6 SPDT Relays
2 Solid State Relays
The 8 open collector drivers for the above
Can be used with the SSR expander.
Cannot be used with the Servo expander.
Solid State Relay Expander for MLFS 1
The Solid State Relay Expander allows for:
1 DPDT Relays
7 Solid State Relays (2A 230v)
The 8 open collector drivers for the above
Can be used with the Relay expander.
Cannot be used with the Servo expander.
Servo Expander for MLFS 1
The Servo Expander allows upto 9 additional Radio Control servos to be attached to your
Simulator system.Cannot be used with the relay or ssr expander.
Servo Expander for MLFS 2
The Servo Expander allows upto 9 additional Radio Control servos to be attached to your
Simulator system.